Resolved QHY600 will not open

Discussion in 'STC Series CMOS' started by Peter Bresler, Feb 21, 2022.

  1. Peter Bresler

    Peter Bresler Cyanogen Customer

    Joined:
    Jan 30, 2020
    Messages:
    90
    Location:
    Los Osos, CA
    My QHY600 does not open. I use the ASCOM driver. The camera opens when I select the CCD capture, I click OK, but when I try to connect it fails.

    Peter Bresler
     

    Attached Files:

  2. Colin Haig

    Colin Haig Staff Member

    Joined:
    Oct 27, 2014
    Messages:
    7,379
    Location:
    Earth
    Hi Peter, from the log, MaxIm is successfully connecting to Camera 1, the main camera.
    It is failing to connect to Camera 2, the guide camera.
    So, if the QHY600 is your main imaging camera (Camera 1) that is working.
    What's the guider camera you have?
     
  3. Colin Haig

    Colin Haig Staff Member

    Joined:
    Oct 27, 2014
    Messages:
    7,379
    Location:
    Earth
    One other tip: Some users report certain ASCOM cameras are not thread-safe, so turn this ofF:
    threading_off.png
     
  4. Peter Bresler

    Peter Bresler Cyanogen Customer

    Joined:
    Jan 30, 2020
    Messages:
    90
    Location:
    Los Osos, CA
    I also have a ZWO290, but that is not the camera I need to do the pointing model, it is the QHY600; everything seemed to work up to the point a capturing an image; then an error message is generated.
     
  5. Colin Haig

    Colin Haig Staff Member

    Joined:
    Oct 27, 2014
    Messages:
    7,379
    Location:
    Earth
    MaxIm is indicating a problem with the second camera - and that is the cause of the error.

    Verify you have the first and second camera set up properly.

    First Camera (QHY600):

    Camera Control Window, Setup tab.
    Camera 1 [Setup] Camera Model = ASCOM.
    [Advanced...]
    ASCOM Camera Chooser
    Select QHYCCD-CamerasCapture
    [Properties]
    Now select the QHYCCD 600.
    OK a bunch of times.

    Second Camera (ZWO290):

    Camera Control Window, Setup tab.
    Camera 2 [Setup] Camera Model = ASCOM.
    [Advanced...]
    ASCOM Camera Chooser
    Select ASI Camera (1)
    [Properties]
    Now select the ZWO 290.
    OK a bunch of times.

    Now it should connect.

    Alternative:
    You could also set Camera 2 [Setup] Camera Model = No Camera.
    That would disable the guide camera.
     
  6. Peter Bresler

    Peter Bresler Cyanogen Customer

    Joined:
    Jan 30, 2020
    Messages:
    90
    Location:
    Los Osos, CA
    I think I did those things. The QHY settings window for the QHY600 opened up. Maybe we can do a Teamviewer tomorrrow if I can't get it to work....no time now.

    Peter
     
  7. Colin Haig

    Colin Haig Staff Member

    Joined:
    Oct 27, 2014
    Messages:
    7,379
    Location:
    Earth
    Let me know what time you have in mind. I'm tied up from 2:30 to 5pm EST tomorrow.
     
  8. Peter Bresler

    Peter Bresler Cyanogen Customer

    Joined:
    Jan 30, 2020
    Messages:
    90
    Location:
    Los Osos, CA
    Maybe 11AM PST tomorrow? I will try it without threading.
     
  9. Colin Haig

    Colin Haig Staff Member

    Joined:
    Oct 27, 2014
    Messages:
    7,379
    Location:
    Earth
    Ok, let's go for then. Send me a PM tomorrow with you telephone number, and if you need it, I can send a link for TV QuickSupport.
     
  10. Colin Haig

    Colin Haig Staff Member

    Joined:
    Oct 27, 2014
    Messages:
    7,379
    Location:
    Earth
    Problem was Camera 2 was set to a non-existent camera, so MaxIm failed to open that.
    Camera 1, the QHYCCD 600 worked fine.
     

Share This Page